motogadget mo.unit blue (with mo.ride app)

Details:
The new mo.unit blue has been further developed and significantly improved over the proven previous version. It now has 12 inputs and 10 outputs, exchangeable quality cable clamps and above all Bluetooth® LE. Thus the mo.unit blue can be connected directly with our App ´mo.ride´ on the Smartphone. This functionality is unique in the motorcycle accessories sector.

The entire setup and alarm system can be controlled via the mo.ride app. Fault diagnosis is also possible during operation and without removing the mo.unit. A secure, encrypted keyless go function can also be used.

When activated, the approach with your own smartphone is sufficient to get the vehicle ready to start. Thus, the on-board voltage can be switched on by pressing the start button. Pressing it again will then start the engine. Once switched on, the on-board power supply remains safely activated while driving, even without a phone.

The mo.unit blue is the digital control unit for a motorcycle, the heart of the entire vehicle electrical system. It can be operated with push-button controls or with conventional, shifting handlebar controls. It switches all necessary components on the vehicle and at the same time it takes over the tasks of the electrical fuses.

Relays and individual components in the wiring harness are greatly reduced and a new, minimized wiring of the vehicle can be carried out in a very short time.

When using the mo.button, the number of all switch fitting connections is reduced to a single cable.

Features WITHOUT Smartphone and mo.ride App:

• Complete digital probe control, 4-pushbutton or 5-pushbutton operation possible
• Complete replacement for the fuse box. 10 independent circuits are digitally monitored and switched off in case of malfunctions. After elimination of the fault, the fuse function is automatically reset
• Integrated, position-independent alarm system
• Integrated, digital, load-independent flasher relay, automatic switch-off optional and adjustable, mo.wave mode selectable
• Integrated hazard warning lights
• turn signal optionally adjustable as position light
• parking light and headlight flasher integrated
• Control of dipped and main beam (up to 200 W switching capacity) with only one push button
• Integrated, digital brake light modulator, flashing mode programmable
• Acceleration-controlled hazard brake light (automatic warning signal)
• Integrated starter relay for starters with magnetic switch (up to 30 A switching capacity)
• Intelligent and configurable control/disconnection of the loads to be able to use the maximum starting energy of the battery during the starting process
• Integrated, digital horn relay
• Two configurable additional outputs AUX1 and AUX2
• Diagnostic function for assignment of input, output, switching status of the circuit, short-circuit diagnosis etc.
• Calibration and current measurement enables defect detection of all illuminants
• Features WITH Smartphone and mo.ride App
• Encrypted connection via Bluetooth® LE (low energy), therefore tamper-proof
• extremely low power consumption of Smartphone and mo.unit blue (with active Bluetooth 0.9mA and in Powersave mode after 6 weeks of inactivity: 0.3mA)
• Keyless-Go (readiness of the vehicle to start by approaching it with your own smartphone)highly sensitive accelerometer allows you to display your driving activity in mo.ride by an activity factor, number of turns, top speed, etc.
• Transmission of alarm events (with date, time, vehicle on the ground etc.) to the App
• Setting of mode and sensitivity of the alarm system
• Monitoring of the current battery voltage in the app
• Diagnosis of all inputs and outputs, measurement of currents, voltage, device temperature
• Defect detection of all illuminants by calibration. Defective blinkers cause a doubling of the blinking frequency, status message in the app and audio message by Rideassist.
• Rideassist: optional flasher sound and error messages in real time as audio output via helmet headset.
• Manual switching of the outputs via Smartphone (except Starter)
• Firmware updates without removal at any location via Smartphone and App
• Configuration of the setup menu without removal at any location via Smartphone and App
• Vehicle management with automatic hints on maintenance tasks, condition of tires, chain, brake pads, oils, fuel, spark plugs etc. by comparing the vehicle mileage by means of a speedometer signal
• Logbook records trips and stores all generated vehicle messages, alarm events and maintenance tasks
• Display of parking position and Ping! to help with vehicle search
• LIN-Bus connection available for later connection of suitable motogadget products

compatibility:
iPhone as of iOS 10 / Android as of 8.0 (compatibility may be limited by manufacturer)
Further information about the app is also available at mo.ride.de or in Google Play and iTunes.

Scope of delivery:

• mo.unit blue
• 1 x M5 stainless steel screw
• 2 x M5 stainless steel screw with nut
• 1 x tacho sensor with 2 magnets
• Detailed installation and operating instructions

Specifications and Features

• L/W/H: 90 x 53 x 30 mm, bore distance 74 mm
• Weight: approx. 180 g
• Mounting: 2 x M5 stainless steel screws (mounting and ground connection), 1 x M5 screw contact for battery plus
• Operating voltage: 6 V - 20 V
• Operating temperature: -20°... +80°C


• Inputs:


1 x input (+12V switched) for ignition lock or mo.lock
11 x control input (minus/ground switched) for:


1. Turn signal left
2. Turn signal right
3. Low-beam/main beam
4. starter
5. horn
6. Brake light
7. Kill switch
8. stand switch
9. LIN-Bus
10. AUX1
11. AUX2


• Outputs:


10 x output (+12V) for:


1. Turn signal left
2. Turn signal right
3. Dipped beam
4. high beam
5. starter
6. horn
7. Brake light
8. ignition
9. AUX1
10. AUX2